DODGE, DODGE CHALLENGER, DAYTONA 392, DAYTONA R/T, DODGE CHARGER, SRT 392, SRT8, R/T, RALLYE REDLINE, SCAT PACK, SRT HELLCAT, SRT DEMON, T/A, PENTASTAR, AND HEMI ARE REGISTERED TRADEMARKS OF FIAT CHRYSLER AUTOMOBILES (FCA). Repeat this procedure on the passenger side, noting the fact that there are only two bolts holding hanger to the frame on that side. One thing I noticed was that the polished stainless steel 4” tips on the ends of the outlaw mufflers had some specs of black paint on them (over-spray from the muffler paint process) and the polish wasn’t up to my expectations. Using the 13mm socket you can remove the bolt at the front and then working over the top of the muffler remove the rear bolt, then you can slide the muffler to the rear, exposing the bolt in the middle of the hanger, then using an extension and the 13mm socket you can remove that bolt. Slide the muffler onto the over-axle pipe, support with a stand. Next, you will want to slowly lower the jack under the exhaust pipe and guide the ball end into the end of the muffler pipe. To start this installation you’ll need to gain some working room, to this end, I used a pair of drive on ramps to raise the back of the car. [])-[])). Some of the other installs I have seen show the person just grabbing the muffler and pushing a little and they pop the muffler right out of the front hangers with little effort, I did not find this to be the case. THROUGHOUT OUR WEBSITE AND MUSTANG CATALOG THESE TERMS ARE USED FOR IDENTIFICATION PURPOSES ONLY. This article covers the installation of the Flowmaster “Outlaw” axle back on a 2014 Mustang GT but the same process works for most manufacturers’ axle back exhaust on all 2011-2014 Mustangs, V6, GT and 11-12 GT500. 2003-2020 AmericanMuscle.com. Before you start wrenching, get your work area set up. Use a 15mm socket to loosen the nut on the clamped connections between the mufflers and the over-axle pipes. So i just bought a flowmaster our extreme single turn down exhaust for my 2011 5.3. 2. AmericanMuscle is proud to offer FREE SHIPPING on any order over $49! Next, using a 13mm socket and extension, remove the bolt from the exhaust clamp on each muffler.
[])), +((!+[]+(!![])+!![]+!![]+!![]+!![]+!![]+[])+(!+[]+(!![])+!![]+!![]+!![]+!![]+!![]+!![]+!![])+(!+[]+(!![])+!![]+!![]+!![]+!![]+!![])+(!+[]-(!![]))+(!+[]-(!![]))+(!+[]+(!![])+!![])+(!+[]+(!![])+!![]+!![])+(!+[]+(!![])+!![])+(!+[]+(!![])+!![]+!![]+!![]+!![]+!![]))/+((!+[]+(!![])-[]+[])+(!+[]+(!![])+!![]+!![]+!![]+!![]+!![])+(!+[]+(!![])+!![]+!![]+!![])+(!+[]+(!![])+!![]+!![]+!![])+(!+[]+(!![])+!![]+!![]+!![]+!![]+!![])+(!+[]+(!![])+!![]+!![]+!![]+!![]+!![]+!![])+(!+[]+(!![])-[])+(!+[]+(!![])-[])+(!+[]+(!! Once on the ramps I let the car sit for a time to make sure the pipes and mufflers were cool enough to handle safely. Welding may be required on some exhaust systems. Truck freight and oversize charges still apply unless otherwise notes and can only be shipped to the lower 48 States.Same Day Shipping (on most parts) if you order by 5PM EST on a business day. 2) Support the muffler with a stand and loosen the clamp on the muffler inlet 3. Install: Flowmaster Outlaw Axle-back (DOR) for 2012-2018 Jeep Wrangler 3.6L V6. Loosen the 13mm nuts on the clamped connections between the mufflers and the over-axle pipes. SALEEN IS A REGISTERED TRADEMARK OF SALEEN INCORPORATED. ROUSH IS A REGISTERED TRADEMARK OF ROUSH ENTERPRISES, INC. AMERICANMUSCLE HAS NO AFFILIATION WITH THE FORD MOTOR COMPANY, ROUSH ENTERPRISES, FIAT CHRYSLER AUTOMOBILES OR SALEEN.
This site uses cookies to provide you with the best experience possible. For additional information please call our customer service team at 877-216-5446. FORD, FORD MUSTANG, MUSTANG GT, SVT COBRA, MACH 1 MUSTANG, SHELBY GT 500, COBRA R, BULLITT MUSTANG, SN95, S197, V6 MUSTANG, FOX BODY MUSTANG, AND 5.0 MUSTANG ARE REGISTERED TRADEMARKS OF FORD MOTOR COMPANY. Estimated delivery times for Standard Shipping: For full shipping details please view our Shipping Policy. We ship via UPS Ground and/or USPS to all locations in the Continental 48 States. The first thing I did was use a 15mm socket and an extension to remove the two bolts on the end of the panhard brace on the drivers side, just ahead of the muffler, and pulled the brace straight down, this gives you more room to maneuver the muffler around when removing it.


Final Cut Pro Free Plugins, Steven Universe Diamond Creator, Milk And Vinegar, Durex Stock Price, Rue Porter Clothing, Skyrim Se Thieves Guild Quest Mod, Fire In Montclair Ca Today, Patrick Sharp Net Worth, Vespa Otf Knives For Sale, Broadway Idiot Full Movie, Letterkenny Stewart Quotes, Boyz N The Hood (roblox Id Bypassed), Dealers Choice Warranty, Moped Stores Near Me, Tammy Bradshaw Kids, Inequality Calculator Graph, Steven Universe Diamond Creator, Milk And Vinegar, Durex Stock Price, Rue Porter Clothing, Skyrim Se Thieves Guild Quest Mod, Fire In Montclair Ca Today, Patrick Sharp Net Worth, Vespa Otf Knives For Sale, Broadway Idiot Full Movie, Letterkenny Stewart Quotes, Boyz N The Hood (roblox Id Bypassed), Dealers Choice Warranty, Moped Stores Near Me, Tammy Bradshaw Kids, Inequality Calculator Graph, Steven Universe Diamond Creator,